Settings

General server settings

bg-dots
bg-dots

The System → Settings section is used to configure the numbering plan, SIP and H.323, network interfaces, NAT, P2P, anonymous connections, SNMP, LDAP, cascading, diagnostics, SSL, and power controls.

Conferences must be finished before changing settings; new values are applied about a minute after save. Production network interface settings are not saved on the stand if that would break access.

Tab navigation

  • “Main” – number ranges, network, SIP, time, and language.
  • “H.323 settings” – H.323 signaling and gatekeeper.
  • “Network interface settings” – interface addresses.
  • “Routes” – IP routing table.
  • “NAT” – external IP, STUN, RTP, and ICE.
  • “P2P” – P2P recording and proxying.
  • “Anonymous connection” – anonymous participant parameters.
  • “SNMP” – SNMP server.
  • “LDAP” – account synchronization.
  • “Cascading” – media server list.
  • “Diagnostics” – Ping, Traceroute, Tcpdump, Logs.
  • “SSL” – web interface certificate.
  • “Reboot” – server reboot.
  • “Shutdown” – server shutdown.

Main

Range id settings

  • “Prefix” (accounts) – account number prefix; 0 to 10 digits.
  • “from” / “to” (accounts) – account number range.
  • “Prefix” (conferences) – conference number prefix.
  • “from” / “to” (conferences) – conference number range.
  • “from” / “to” (LDAP) – number range for LDAP accounts.

Network

  • “Firewall whitelist” – networks in CIDR format; if empty, the firewall is disabled.
  • “Trusted proxies” – trusted proxy networks in CIDR format; localhost is always trusted.

H.239 settings

  • “Send content in mainstream” – send the second stream in the main video. Available values: “No”, “Yes”.

Other settings

  • “Allow to make group calls” – allow WS accounts to make Add-Hoc calls.
  • “Server name” – display name of the server.

SIP settings

  • “Signal port” – SIP signaling port. Default is 5060.
  • “RTP timeout” – RTP timeout, seconds. Default is 60.
  • “Encryption” – “Disabled”, “Enabled”.

Service type

  • “TOS decimal” – TOS value for IP packets. Default is 16.

Time settings

  • “Time zone” – server time zone.
  • “Date and time” – set date and time.
  • “NTP” – NTP server address.

Interface settings

  • “Default language” – language of splash screens and voice prompts. Available values: Russian, English, Dutch, French, Spanish, German, Vietnamese.

Setting up a domain name

  • “Domain name” – domain used to reach the server.

  • “Save” – save the tab settings.

H.323 settings

  • “Signal port” – H.323 signaling port. Default is 1720.
  • “RTP timeout” – RTP timeout, seconds.
  • “from” / “to” – port range for H.225/H.245.
  • “Determine users by H.323 alias (aka UserByAlias)” – call users by the number in the account list.
  • “Use gatekeeper” – gatekeeper mode.
  • “Save” – save the tab settings.

Network interface settings

Shows the interface (for example, eth0).

  • “IP” – IPv4 address.
  • “Network mask” – subnet mask.
  • “Gateway” – default gateway.
  • “MTU” – maximum packet size.
  • “DNS” – DNS address.
  • “Add” – add a network interface.
  • “Save” – save interface parameters.
Attention!
After network changes, routes added on the “Routes” tab are deactivated. Production addresses are not saved on the stand.

Routes

IP routing table with network, whether the route is in the table, and “Actions”.

  • “Add” – add a static route.

NAT

NAT parameters

  • “External IP” – NAT border device address.
  • “SIP” – apply NAT for SIP.
  • “H.323” – apply NAT for H.323.
  • “Local networks” – local networks that do not receive the external IP; one network per line, without CIDR.

STUN

  • “STUN address” – STUN server address. Default is 127.0.0.1.
  • “STUN port” – STUN port. Default is 3478.

RTP parameters

  • “Start” – first RTP port.
  • “End” – last RTP port.

WebRTC ICE servers

  • “List of ICE servers” – JSON array of RTCIceServer objects.

  • “Save” – save the tab settings.

P2P

  • “On” – P2P call recording.
  • “Resolution” – recording resolution.
  • “Video-on-hold p2p calls” – waiting video.
  • “Auto loop” – repeat the waiting video.
  • “Proxy websocket clients P2P calls” – only signaling goes through the server.
Attention!
When “Proxy websocket clients P2P calls” is on, P2P recording is not available.
  • “Save” – save the tab settings.

Anonymous connection

  • “Bandwidth for SIP and H.323 participants” – bitrate.
  • “Resolution for SIP and H.323 participants” – resolution.
  • “FPS for SIP and H.323 participants” – 15, 25, 30, 60.
  • “Bandwidth for WS participants” – WebSocket bitrate.
  • “Resolution for WS participants” – WebSocket resolution.
  • “FPS for WS participants” – WebSocket frame rate.
  • “Create an anonymous room” – create a temporary room if it does not exist.
  • “H.323 Crypto” – H.323 encryption.
  • “Filtering RTP” – block extra media streams from the same port.
  • “Allow anonymous connection to the server” – anonymous calls to the server.
  • “Allow anonymous connections to auto attendant” – move from auto attendant.
  • “Allow anonymous connections to call accounts” – call registered accounts.
  • “Codecs” – allowed codecs; selection is done by moving items between lists.
  • “Save” – save the tab settings.

SNMP

  • “Enable SNMP server” – start SNMP.
  • “Access from network” – network allowed to access SNMP.
  • “Community” – SNMP community.
  • “Download MIB file” – download the MIB.
  • “Save” – save the tab settings.

LDAP

  • “Turn on account synchronization over LDAP” – enable synchronization; save settings and run a connection check.
  • “Server IP” – LDAP address.
  • “Server port” – port; default is 389.
  • “Scheme” – ActiveDirectory, OpenLDAP, FreeIPA.
  • “Encryption” – None, SSL, TLS.
  • “User” – bind account.
  • “User password” – LDAP password.
  • “Base DN” – search base DN.
  • “Search filter” – LDAP filter.
  • “Username attribute” – login attribute; default is userprincipalname.
  • “User prefix” – prefix (for OpenLDAP).
  • “User suffix” – domain suffix.
  • “User number attribute” – number attribute (for example, ipPhone).
  • “Account type” – WS (web client), Loop (Skype4b).
  • “Assign numbers automatically” – assign numbers automatically (WS).
  • “Use a userPrincipalName attribute as a number” – use userPrincipalName as the number (WS).
  • “Allow automatic registration” – allow registration before adding to a conference (WS).
  • “Connection check” – test the connection.
  • “Save” – save the tab settings.

Cascading

  • “Add” – add a media server.
  • “Server name” – Latin name.
  • “IP” – media server address.
  • “Port” – incoming connection port.
  • “Backup Port” – backup MCU port.
  • “Local IP” – master server address.
  • “Password” – remote administrator password.
  • “Processor” – processor assignment.
  • “Debugging mode for the main MCU” – main MCU debug mode.
  • Status – connection state.
  • “Switch to a backup MCU” – switch to the backup media server.
  • “Save” – save the tab settings.

Diagnostics

Subsections: “Ping”, “Traceroute”, “Tcpdump”, “Logs”.

Ping

  • “IP” – host address or name.
  • “Ping” – run the check.

Traceroute

  • “IP” – host address or name.
  • “Traceroute” – run traceroute.

SSL

Attention!
If any field is set incorrectly, the default certificate is used.
  • Certificate – certificate chain (BEGIN CERTIFICATE / END CERTIFICATE).
  • Private key – private key (BEGIN PRIVATE KEY / END PRIVATE KEY).
  • Certification Authorities (CA) – root CA.
  • “Save” – apply the certificate.

Reboot

Opens a confirmation dialog. Reboot is not confirmed on the stand.

  • “Cancel” – close the dialog.
  • “Reboot” – reboot the device.

Shutdown

Opens a confirmation dialog to shut down the server. Shutdown is not confirmed on the stand.

  • “Cancel” – close the dialog.
  • “Shutdown” – power off the device.
Gateways Incoming calls